Blending stump, tortillon and kneaded eraser: how to use them

Updated:

A blending stump (or tortillon) is a rolled-paper tool you rub over pencil marks to smooth them into soft gradients. A kneaded eraser does the opposite job: it lifts graphite to make highlights or clean edges. Use the stump to blend and the kneaded eraser to take tone away.

What is a blending stump?

A blending stump is a pencil-shaped tool used to smudge or blend marks made with charcoal, Conté crayon, pencil and other media. According to Wikipedia, most stumps are compressed paper rolled into a rod and sanded to a point at each end, though some are felt or leather. They come in sizes for large areas and fine detail.

Blending turns visible pencil strokes into a smooth tone. This suits soft subjects such as skin, clouds or a sphere. It is optional, though: plenty of realistic drawings use only layered pencil strokes.

What is a tortillon, and how does it differ?

A tortillon is a variant of the stump. Wikipedia describes it as less tightly packed, with a hollow core. Many shops sell the two under similar names, and in everyday use artists often treat them as the same thing. If you are buying one tool, a medium stump is a safe choice. A tortillon can be handy for tight corners, since it is lighter and softer.

How do I blend with a stump?

  1. Lay down graphite. Shade with a soft pencil such as 2B or 4B. Eckersleys notes that soft B pencils have more graphite and leave darker marks.
  2. Hold the stump at an angle. Wikipedia notes that this increases the surface area in contact with the paper.
  3. Use small circular or back-and-forth motions. Work from dark to light, so you pull tone into the lighter area rather than the reverse.
  4. Add more graphite on top if the area gets too pale, and blend again lightly.
  5. Finish with edges. Sharpen your pencil and re-draw the sharp edges that blending softened.

Use light pressure. If you push hard, the stump will press the graphite into the paper's tooth, and the tone becomes difficult to adjust. Try it on the shading worksheets before using it on a drawing, or on the shading of the apple lesson.

Should I use my finger or tissue instead?

You can, and many beginners do. Wikipedia points out that finger smudging can achieve similar effects but leaves skin oil on the paper, making the surface less receptive to the medium. A tissue or cotton bud avoids that, and a stump gives the most control for small areas. Treat the stump as a convenience you can add later. Our drawing supplies for beginners guide lists what to buy first.

What does a kneaded eraser do?

A kneaded eraser, also called a putty rubber, is a pliable eraser made of unvulcanised rubber that you can shape with your fingers. According to Wikipedia, it lifts graphite, charcoal and other media by absorbing the particles, does not wear down and leaves no eraser crumbs. It can fully remove light marks but is poor at removing dark areas, and it can smear or stick when warm.

That makes it more of a drawing tool than a correction tool. You can press it into a shaded area to lift a highlight, pull it across to soften an edge or dab it to reduce tone without damaging the paper.

How do I use a kneaded eraser for highlights?

Pinch off a piece and knead it into a point or a flat edge. Press it onto the shaded area and lift straight up, rather than rubbing. Repeat for a graduated highlight. For a thin highlight line, flatten the eraser into a ridge. On a sphere, lift a soft spot where the light hits and a thin band of reflected light along the shadow edge. The mushroom lesson ends with exactly this: highlights lifted with an eraser.

How do I clean and store them?

For a stump, Wikipedia says artists often use a sandpaper pointer to clean and re-sharpen a dull tip, and recommends keeping the tip clean when blending light areas. Keep separate stumps for light and dark if you can.

For a kneaded eraser, knead it until the graphite folds into the mass. When it is saturated and starts leaving marks, rinse it thoroughly with water and knead it again. Wikipedia notes it can last indefinitely if washed and kneaded regularly. Store it in a small tin so it does not collect dust.

Do I need all three tools?

No. Start with a kneaded eraser, since it is useful from day one. Add a stump when you want smoother tones. More guidance on pencils is in pencil grades explained, and the rest of the series is on the drawing supplies hub. You can practise highlights on the apple lesson.

What mistakes do beginners make with blending?

The most common one is blending too early, before the tonal shapes are right. Blending only softens what is already there, so if the shadow is in the wrong place, smudging will not fix it. Get the shapes right with plain pencil strokes first, then blend.

The second is over-blending until everything is the same grey. Leave some areas crisp, such as the edges of objects, so the drawing keeps contrast. The third is a dirty tool: a stump loaded with dark graphite will leave grey streaks in a light area. Keep a clean one for highlights, and wipe the paper clean of loose graphite dust with a soft brush rather than your hand. Finally, resist blending an entire page. A few soft areas next to a few crisp ones usually look more convincing than a fully smudged surface.

To see blending and lifting in context, Guidart (free on iPhone and iPad) has voice-guided shading lessons for real paper, with optional AR. A photo of the finished drawing gets an AI score with tips on shading. The score is not real-time and not a human teacher.

Sources

  1. Wikipedia: Stump (drawing)
  2. Wikipedia: Kneaded eraser
  3. Eckersleys: What are pencil grades?

Frequently asked questions

What is the difference between a blending stump and a tortillon?

Both are paper tools for smudging graphite. A stump is tightly packed, while a tortillon is less tightly packed with a hollow core. In practice many artists use the names loosely.

Can I just use my finger to blend?

You can, but fingers leave skin oil on the paper, which makes the surface less receptive to graphite. A stump or tissue avoids that and gives you finer control.

How do I clean a blending stump?

Rub the tip on a sandpaper pad or a scrap of fine sandpaper to remove graphite and re-sharpen it. Keep a separate stump for light areas so you do not drag dark graphite into them.

How do I clean a kneaded eraser?

Knead it until the graphite folds into the mass. When it starts leaving marks instead of lifting them, it is saturated; rinsing it thoroughly with water and kneading it again removes the build-up.

Related pages

GuidartLearn to draw on paper, free on iPhone and iPad
Download